• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace a Kia Sportage Replacement Key

The key of a lot of Kia models comes with a keyless entry system built into. This key usually resembles an remote control, and can be exchanged with a new one from a Kia dealer or locksmith.

Key fobs may stop working due to a number of reasons, such as a dead battery, worn-out buttons signal interference or water damage. Here are some tips to assist you in getting your Kia key fob that is a replacement for the sportage again.

How to replace a smartkey or remote key?

The battery in your Kia's intelligent key will eventually have to be replaced, regardless of whether it's a remote as well as a push-to start key or a regular metal key that is not equipped with transponder. This is especially relevant if your vehicle shows a message that states the smart or remote keys have low battery power.

It's a simple process. To replace the battery on the keyfob remove the mechanical key from the slot at the back of the fob. Then, pull the cover off. Inside the key fob will be a small screw that holds the battery in the correct position. Take out the old battery by unscrewing the screw with a small screwdriver. Then, you can insert the new battery and close the slit on the key fob.

When the key fob is equipped with an updated battery check it by pressing the locks and unlock buttons. If the doors unlock and lock in the same way, you're good to go! You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers feel cold or you have to run errands around Brandon.

Not all key fobs might need to be programmed (transponder chips or smart keys). This requires a programing machine that is only available to the locksmith who works for the automotive dealer. Other keys (non-transponder metal keys) don't require programming. If you're looking to reprogramme your key, it is necessary to write down the key code's number on the tag for the key code.

How do you replace a dead battery?

If the 2013 kia Optima Key key fob doesn't respond when you press the lock/unlock button, it's a sign that the battery is insufficient. A battery that is not functioning properly could cause other issues such as the check engine light turning on or the engine not cranking. It is relatively easy to replace the key fob batteries with only the use of a few tools.

Before you begin ensure that your vehicle is turned off and that all doors are closed. Find the small metal or a plastic piece on the bottom of the key fob. Then, jiggle it until the metal key is released. The key can be inserted into the driver door handle to unlock your car.

To replace the key fob battery, remove the cover on the rear and use a plier bar tool to remove the latch that holds the black negative battery cable. Remove the old battery and orient the new battery in a way that the "+" positive side faces you and the "negative" negative side is facing towards the fob's metallic electrical contacts. Push the new CR2032 battery straight into position and avoid excessive force to avoid damaging or bending the contacts of the metal.

After you have installed the new battery after which you turn the key fob on and off in the ignition until the door locks cycle. Then, you can test your Kia key fob to see whether it's working again.

How can you replace the smart key?

You could have the standard keyfob or Smart Key based upon the model of Kia Sportage. The smart key comes with an embedded mechanical key blade while the standard key fob does not. Both types of key fobs are equipped with an internal battery that eventually will need to be replaced. This is a straightforward process that takes less than two minutes.

Make sure to shut off your Kia and stand on a flat or well-lit surface prior to when you begin. Also, keep in mind that there are tiny components inside the fob that can fall out if you are not careful.

The first step is to locate the small release button that is located on the lower backside of your fob. It could be a circular button or rectangular slot. Once you press this button, the mechanical blade will pop out and you can then open the key fob.

After the key fob has been open, remove the battery. The new battery is one called CR-2032 and can be purchased through the internet or at a local auto parts shop. After you're done, your key fob should be able to lock the vehicle, unlock it, and then start your vehicle even if it's not running.

How do I replace the mechanical key

The Kia key fob is an amazing convenience that allows us to lock and unlock our car at the press of the button. Like all devices that is used, the kia rio key key fob may have issues. There are ways to resolve these issues and ensure that our key fobs are in good working order for the long run.

A dead or drained battery is among the most frequent problems. This could cause the fob to stop working altogether or even to stop working intermittently. If this is the case you should replace the battery with a fresh new one.

If this does not solve the issue, you can use an ordinary screwdriver with a flat head to wedge the fob's casing made of plastic open. Be careful not to damage any internal components, or scratch the plastic. Once the battery is opened, carefully remove the battery you have been using and replace it with a brand new one.

After the new battery has been put installed, close and unlock the doors with the mechanical key (every Kia fob has an emergency mechanical key that can fit into the slot). Test the key fob to confirm it's working as intended. If the key fob not working, contact a dealer or locksmith to help resolve the issue. To avoid future lockouts, make sure you get an emergency key that can work in all of the door and trunk cylinders.