• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace the Replacement Key Battery For the Saab 9-3

saab key battery owners must follow a set of unique steps to add a second ignition key. This requires a handheld computer, called Tech-2 which is to be used by the dealer. A new key and transponder must be purchased and programmed to the car.

It is a good idea to rotate your keys so that one does not wear out more quickly than the other. This will also help to keep your keys in top shape.

Replacement Case

The new key fobs for keys are not like the older Saab keys. They are equipped with electronics which make it hard to duplicate. That has made car theft significantly more difficult than it was twenty years ago. It has also made it more costly to replace keys that were lost.

Every owner of a Saab 9-3 must have at minimum two working keys. It's expensive to replace a lost key because it requires replacing the CIM module, as well as reprogramming the locking cylinders. Dealers charge between $100 and $200 for this.

There are ways to cut down on the high cost. Some parts suppliers will use the code of the spare key to cut a brand new metal blade for a fraction of what the dealer charges. The key must be the exact same as the original to allow it to work in your vehicle.

Follow these steps to replace the case. You'll require a flathead screwdriver and some patience. With the screwdriver, break apart the plastic and remove the emergency key. Once you have the case open, remove the electronics and place them into your new case. Make sure you put the correct key and badge back in the case too.

Replacement Battery

The replacement battery for the Saab 9-3 is a low-cost component that can be replaced easily and quickly. This YouTube DIY video Cyclone Cyd shows how to replace the battery in the remote key fob in only four steps. This guide should work with any modern saab key fob, although the process might differ slightly.

This button is usually located just below the Saab logo on the back of the fob. It's usually close to the Saab logo on the back of the fob. Next you will need an screwdriver with a flat head to insert into the small hole of this button. This will be enough to allow you to open the fob's case so that you can replace the battery.

Once you have installed the new batteries CR1632, it is possible to reassemble your remote key fob. Then, you can program it into your car. The entire process should take no more than an hour at most. It is a very simple process that does not require any special equipment.

If you lose a key the procedure will be more complicated but it is still able to be completed. The dealer will need to find the VIN number of the car and then order a replacement key blade and TWICE module with the proper unique code. Then, they'll have to cut the replacement key and then program it using a brand new tool for programming called MDI.

Key Replacement Fob

The key fob is the device that locks and unlocks your car. It has a battery within. Batteries have a finite lifespan and eventually will die. It is a common problem in all vehicles. The good thing is that you can replace the battery in all key fobs without having to replace the entire case. You can purchase fobs replacements on Amazon that include all the electronics already installed, which means you can just pop open the case and replace those batteries that are old. It is important to keep in mind that you'll need to take out the emergency key first. you can do this by putting a small flathead screwdriver into the slot that is located in the middle of the case. Work the screwdriver around the case until it is split open, making it easy to remove.

If you are about to replace your keys, make sure you have spare keys, as this can reduce the total cost by a substantial amount. If you have spare keys, you can have the dealer cut an additional key and program it to the car, which is much cheaper than replacing the whole key fob.

If you don't have a spare, it is possible to add another key to your car, but this will require a lot of research and effort. The cost for adding a second key is a few hundred dollars, and it also requires programming of the car's computer. Professionals can accomplish this but it's not a cheap option.

Replacement Ignition

The modern SAAB 9-3 is a more sophisticated alarm system built around a key code. If you lose your primary key, it may be costly to get another one since the car needs to be equipped with a specific computer and be programmed to accept a brand new key. Locksmiths typically aren't able to program this or even a dealer will charge several hundred dollars to program the new key!

If you've lost the only working key, a dealer will repair the computer in your car (known as the CIM or SAAB TWICE) in order to make a replacement, and will charge you a premium price for it. Instead, we can reprogram the EEPROM in your current car computer to prepare it for a new key, and save you over 50% of what you'll have to pay at a dealership.

If you've been a faithful owner of a 03-11 saab 9-3 replacement key 9-3, then you probably realize that the ignition key isn't the most robust. They can get extremely sticky, and the buttons are known to fall off from time to time which is why you should think about buying a new one if the one you have isn't functioning properly. It's not as difficult as it seems to replace the ignition key. With the right tools, it can be accomplished quickly.